ICON On/Off Switch

Easy To Install
The ICON On/Off Switch is easy to install and set up and yet so affordable, you'll want to replace all your switches with ICON Switches. Just remove the old switch, reattach the existing line, load, ground and neutral wires using the included wire nuts, and you're done. If this is your first INSTEON installation, the best way to ensure you get everything needed to provide the most reliable communication between devices is to buy the complete Dimmer Switch INSTEON Starter Kit, which includes everything required to set up your INSTEON network, including two SwitchLinc V2 Dimmers, a pair of SignaLinc RFs to ensure INSTEON network reliability, and the desktop ControLinc. Learn more about INSTEON here.

Not Sure What to Choose?
For more features, increased flexibility and a customizable look, upgrade to the INSTEON SwitchLinc V2 Relay. Below is a comparison between the SwitchLinc V2 Relay and the ICON On/Off Switch.

Smarthome Design Product No.:	SwitchLinc V2 Relay 2476S	ICON On/Off Switch 2876SB
INSTEON Enabled:	Yes	Yes
Maximum Load:	13 amps for inductive loads, 480 watts for incandescent & inductive loads	10 amps for inductive loads, 400 watts for incandescent & inductive loads
INSTEON Scenes:	417	30
Status LED:	Yes (1 white - customizable to blue, red, green, amber Color Change Kit)	Yes (1 amber)
Included paddles:	White only	White only
Changeable paddle colors:	Yes (customizable to ivory, gray, black, brown, and almond)	Yes (customizable to ivory, gray, black, brown, and almond)
Ramp Rate(s):	1, Instant	1, Instant
Preset on level(s):	1, 100%	1, 100%
X10 Ready:	Yes	Yes
X10 Primary Address:	1 Optional (comes unassigned), any of 256 possible	1 Optional (comes unassigned), any of 256 possible
X10 Scenes:	64	0
Warranty:	2 years (upgradeable to 7 years)	1 year

Built with a Quieter Relay
Because the ICON On/Off Switch is built with a much quieter relay than most remote-control ON/OFF switches, it has a click that's more than 80 percent quieter than traditional relay switches. This allows you to control lights and other non-dimmable devices remotely without waking up the baby, annoying other family members, or sending your cat fleeing across the room. The click of the internal relay is barely audible.

Generates Less Heat
Unlike other switches, the ICON On/Off Switch uses a relay to control the load. Other switches use components that absorb about two volts of power and dissipate the heat through the front of the switch. By using a relay, the switch runs cooler and full voltage gets to the load.

Quality Construction
Unlike other switches, the ICON On/Off Switch offers the natural feel of well-built dimmers. You'll love the crisp, tactile response with each touch instead of the mushy feeling of other brands. The amber LED indicates the current on/off status of the lights being controlled. The ICON On/Off Switch is designed and manufactured to high-end specifications and goes through over 10 quality-control tests before arriving at your doorstep. This Decora-style switch will blend with any room's look. A white paddle is preinstalled on each ICON On/Off Switch, but additional paddle colors are available and sold separately. Choose the color that best suits your room's décor: Almond, Black, Brown, or Grey. Two paddles are included in each color-change set. Don't forget to order a matching wall plate.

Create Multi-Way Circuits
The ICON On/Off Switch allows you to customize your lighting setup no matter how your house is wired. It's simple to create a 3-, 4-, or 5-way circuit. First replace all of the existing switches you want to include in the circuit with ICON Switches. The main ICON On/Off Switch must be connected to the standard wires: load, line, neutral, and ground. The secondary relays only need to be connected to the line, neutral, and ground wires. No traveler wires are needed, so it is easy to place one of the relays wherever you need it. Cross-linking all of the companion ICON On/Off Switches to the master ICON switch is the last step in the process for a flexible, fully functional multi-way circuit.

Scene Lighting
Scenes allow you to control multiple lights, rooms or even the whole home with a single command. Because the ICON On/Off Switch can be a member of more than 400 scenes (i.e. "Movie Time," "Party," "Romance," etc.), you'll be able to launch various lighting scenarios with a single button press. These are elegant features usually found only in systems costing tens of thousands of dollars and requiring extensive rewiring of your home. The relays can blend seamlessly in a scene with ICON Dimmers. So one set of lights connected to a ICON Dimmer can slowly dim, while another set connected to the ICON On/Off Switch turns off instantly, all controlled with one command from one button. If you want to control multiple scenes from one controller, upgrade to the KeypadLinc V2 Dimmer.

Compatibility
The ICON On/Off Switch is INSTEON compatible and X10 ready. Homeowners with existing X10 networks can easily migrate to an INSTEON network without having to discard all their existing X10 devices. X10 ready means that it can respond to X10 commands from an X10 controller and it can send X10 commands to X10 devices. Please note that INSTEON devices repeat INSTEON signals but not X10. The ICON dimmer is not X10 scene compatible.

Slim Design
Similar relays are up to 50 percent deeper than the ICON On/Off Switch. Thanks to its slim design, the ICON On/Off Switch makes installation easy even in small junction boxes.

Non-Volatile Memory
All ICON On/Off Switch settings are stored in non-volatile memory and are not lost during power failures. Additionally, in the event of a power loss, the ICON On/Off Switch will return to its last on/off state when power is restored.

Certifications and Warranty
All ICON Switch products are safety approved. The factory for SmartLabs Design Products is ISO9001 certified. In order to meet the ISO 9001 standards, the entire factory underwent rigorous inspections of procedures and policies before being certified. The certification received was based on its dedication to high-quality management systems and strict adherence of quality-control systems and guidelines. Because of this, Smarthome stands behind the entire ICON Switch line of products with a full 1-year warranty.

Specifications
General
ICON Product Number	2876S, / 2876SB, Icon On/Off Switch
Warranty	1 year
Operation
LED Indicator	1 Amber LED
Manual Operation Modes	INSTEON only, X10 only, INSTEON and X10 Combo Mode
Combo Mode Message Order	INSTEON, X10, INSTEON cleanup
Multi-Way Circuit Support	One Icon On/Off Switch controls load, Cross-Link any number of Icon On/Off Switches or other INSTEON Controllers
Setup Memory	Non-volatile EEPROM
INSTEON Features
INSTEON Addresses	1 hard-coded out of 16,777,216 possible
INSTEON Links	30
INSTEON Powerline Frequency	131.65 KHz
INSTEON Minimum Transmit Level	3.2 Vpp into 5 Ohms
INSTEON Minimum Receive Level	1 mVpp nominal
INSTEON Messages Repeated	Yes
Mechanical
Paddle Type	True rocker action
Paddle and Trim Frame Color	White installed, Optional Ivory, Almond, Black, Brown, or Gray
Wire Nuts	3 included
Mounting	Mounts in single or multiple-ganged junction box.
Operating Conditions	Indoors, 40 to 104°F, up to 85% relative humidity
Dimensions	4.1" H x 1.8" W x 1.2" D
Weight	3.6 oz
Electrical
Supply Voltage	120 Volts AC +/- 10%, 60 Hertz, single phase
Surge Protection	MOV rated for 150 Volts
Power Wire Leads	6", 16 AWG, stranded, 600V, 105°C insulation, ends stripped and tinned, LINE (black), LOAD (red), NEUTRAL (white)
Ground Lead	6", 18 AWG, stranded, bare copper
Load Types	Wired-in incandescent lighting and inductive loads
Maximum Load	400 Watts incandescent, 10A resistive
Minimum Load	No minimum load required
Certification	Safety tested for use in USA and Canada (ETL #3017581)
X10 Features
X10 Primary Address	1 optional (comes unassigned)
X10 Scene Addresses	N/A
X10 Status Response	Supported
X10 Resume Dim	N/A
X10 Powerline Frequency	120 KHz
X10 Minimum Transmit Level	3.2 Vpp into 5 Ohms
X10 Minimum Receive Level	10 mVpp nominal
X10 Messages Repeated	No

• ICON On/Off Switch
  
• Quick Start Guide
  
• 2 mounting screws
  
• 3 wire nuts